Helmets
Measure your head circumference correctly - here's how
The right size is crucial to ensure that your helmet fits perfectly and offers maximum protection. You can easily measure your head circumference yourself in just a few steps:Step-by-step instructions
1. prepare the measuring tapeUse a flexible measuring tape (e.g. tailor's tape measure).
2. position it correctly
Place the tape measure about 1-2 cm above the eyebrows and run it horizontally around the head.
Important: The tape should also run across the widest part of the back of the head.
3. measure loosely but correctly and read off the value
Put the measuring tape on tightly, but so that it does not cut in, and read off the circumference in centimetres. It is best to repeat the measurement 1-2 times to check.
Tip for choosing the right helmet
If your measurement is between two sizes, always take the smaller size.The helmet should fit snugly but not cause any pressure points.
No measuring tape to hand?
Simply use a piece of string and then measure.
Shoes and boots
Check shoe and boot size correctly
The right size is crucial for a perfect fit and high wearing comfort. Our size chart is based on the measured foot length and already includes an allowance of approx. 2 cm - so you can adjust your foot length directly.
Step-by-step instructions
1. preparation
Place your foot flat on a sheet of paper.
2. mark the foot
Mark the heel and the longest toe.
3. measure and read off the value
Measure the distance between the markings in centimeters. This value corresponds to your foot length.
Tip for choosing the right shoes and boots
Measure both feet and always take the larger value.
If you are between two sizes, choose the larger size.
No tape measure to hand?
Simply use a piece of string and then measure.
Pants
how to find your perfect trouser size
The right size is crucial to ensure that your trousers fit perfectly and offer sufficient freedom of movement.
Step-by-step instructions
1. measure your waist
Measure your waist at the narrowest point.
2. measure your hips
Measure your hips at the widest point.
3. measure the inside leg length
Measure from the crotch to the desired hem - up to the ankle for long pants, shorter for shorts.
Tip for choosing the right pants
If your measurement is between two sizes, choose tighter or wider depending on the desired fit.
Make sure you have enough freedom of movement.
No tape measure to hand?
Simply use a piece of string and then measure.
Jerseys
how to find the right jersey size
To ensure that your jersey fits comfortably and offers enough freedom of movement, compare your measurements with the information in the graphic:
Step-by-step instructions
1. check shirt length
Use a flexible tape measure.
2. check the chest circumference
Measure under the armpits at the widest part of the chest.
3. check sleeve length
Measure the sleeve length including the neck area.
Tip for the right fit
If your measurement is between two sizes, decide whether you want a tighter or wider fit.
No tape measure to hand?
Simply use a piece of string and then measure.
Gloves
how to determine your glove size correctly
To ensure your gloves fit perfectly and provide a secure grip, simply compare your measurements with the information in our table:
Step-by-step guide
1. check the circumference of your hand
Measure the circumference of your hand without the thumb at the widest point.
2. check hand length
Measure from the wrist/ball of the hand to the middle finger.
3. read off the value
Measure loosely fitting and note the value in centimeters.
Tip for the right fit
The gloves should fit snugly without being restrictive.
If you are between two sizes, take the smaller size if in doubt, as the material can stretch a little over time.
No measuring tape to hand?
Simply use a piece of string and then measure.
Protectors
how to find the right size for elbow protectors
The right size is crucial to ensure that your elbow protectors provide optimum protection and fit securely. You can easily determine your own measurements in just a few steps:
Step-by-step instructions
1. measure your upper arm
Measure the circumference above the elbow at the widest point of the upper arm - where the protector sits.
2. measure the forearm
Measure the circumference below the elbow at the widest point of the forearm, directly under the joint.
3. measure and check values
Hold your arm slightly bent and read off both values.
Tip for making the right choice
The protectors should fit snugly without restricting or slipping.
If you are between two sizes, it is better to take the smaller size, as the material can still stretch slightly during use.
No measuring tape to hand?
Simply use a piece of string and then measure.
how to find the right size for knee protectors
The right size is crucial to ensure that your knee protectors provide optimum protection and fit securely. You can easily determine your own measurements in just a few steps:
Step-by-step instructions
1. measure your thigh
Measure the circumference above the knee at the widest part of the thigh - where the protector will sit.
2. measure the lower leg
Measure the circumference below the knee at the widest part of the lower leg.
3. measure and check values
Bend the knee slightly and read off both values.
Tip for making the right choice
The protectors should fit securely without restricting or slipping.
If you are between two sizes, choose the smaller size if in doubt, as the material still adjusts slightly.
No tape measure to hand?
Simply use a piece of string and then measure.
Choosing the right chest protector
To ensure that your protector provides optimum protection and fits securely, simply compare your measurements with the information in the table:
Step-by-step instructions
1. check the circumference
Measure the chest circumference at the widest part of the chest.
Measure the waist circumference at the point where the protector encloses the upper body - depending on the model, at the narrowest point or where the protector sits.
2. check the length
Compare the length from the base of the neck to the waist and other measurements given in the table with your height.
3. check other lengths
Check all additional measurements, e.g. sleeve lengths on protector shirts or lengths of shoulder and upper body parts, to ensure the fit.
Tip for making the right choice
The protector should fit close to the body without restricting you or slipping. Make sure that all the specified measurements fit comfortably.
No tape measure to hand?
Simply use a piece of string and then measure.
| Products | 0 |
|
|
|
| Total |
0.00
|